Home › Buying Guide
Buying an AC is not just about choosing a brand and checking the price. The room size, cooling capacity, daily usage, inverter technology, installation and warranty can all affect what you spend over time. This guide walks through each decision in order, so you can screenshot the checklists and take them to the shop.
Run through this list before visiting a shop. Anything unchecked is a question for the seller.
A "ton" is cooling power, not weight: 1 ton equals 12,000 BTU per hour. Capacity matters because an undersized unit runs constantly without ever catching up, while an oversized one costs more upfront and switches on and off in a way that can leave the room feeling damp. Room area alone is not enough. Sun, ceiling height, floor level, insulation, occupants and appliances all add heat the AC must remove.
| Room situation | Starting point |
|---|---|
| Small shaded bedroom, ~100–130 sq ft | 1 ton |
| Medium bedroom, ~130–180 sq ft | 1.5 ton (most common) |
| Larger bedroom or living room, ~180–260 sq ft | 2 ton |
| Large open space, shop, high heat load | 2.5 ton+, or professional sizing |
Measure length × width for square footage and note sun exposure, floor level and window area. Top-floor and west-facing rooms carry higher heat load and may need the next size up. See 1 ton, 1.5 ton and 2 ton guides.
| 1 Ton | 1.5 Ton | 2 Ton | |
|---|---|---|---|
| Typical use | Small bedrooms, studies | Medium bedrooms, small living rooms | Large rooms, offices, shops |
| Cooling power | 12,000 BTU/hr | 18,000 BTU/hr | 24,000 BTU/hr |
| Purchase cost | Lowest of the three | Mid-range, most models to choose from | Highest, plus heavier wiring needs |
| Electricity | Lowest draw at full load | Middle; the most common daily driver | Highest draw; benefits most from inverter tech |
Undersizing shows up as an AC that runs for hours yet never reaches the set temperature, with uneven corners. Oversizing shows up as short on-off cycling, a room that feels cool but clammy, and money wasted upfront. When between sizes, the room's sun and floor level should tip the decision, not the price tag.
An inverter varies compressor speed up and down to hold the set temperature. A non-inverter (fixed-speed) runs full blast, cuts off, then restarts as the room warms. That single difference drives everything else: inverters cost more upfront, run steadier and quieter over long hours, and use more specialised electronics when they need repair. Non-inverters cost less to buy and any local technician understands them.
Long daily cooling through summer favours inverter. Brief use in a guest room keeps non-inverter competitive. No fixed savings percentage is quoted here, because real savings depend on the model, room, thermostat setting, weather and operating pattern. Read the full inverter comparison and non-inverter notes.
What decides the bill: cooling capacity, rated input power, whether the compressor is inverter-driven, thermostat setting, daily hours, outdoor temperature, insulation, occupants and maintenance. The basic maths is simple:
Energy use ≈ average power (kW) × operating hours. Estimated cost ≈ energy use × your per-unit tariff from your electricity bill.
Example only: if an AC averages 1.0 kW while operating for 6 hours, the simple calculation is about 6 kWh for that day. Actual consumption can be lower or higher because compressors cycle and inverter models change their operating level. To cost it, multiply by the per-unit rate printed on your own DPDC, DESCO or other distributor bill. Tariff slabs change, so always use a current bill, never a remembered rate.
You will meet several efficiency terms: EER (efficiency at one rated condition), SEER/CSPF (seasonal figures over varied conditions) and star ratings on labels. The rule that matters: compare the same metric at equal capacity. A 5-star 1 ton and a 3-star 1.5 ton are not directly comparable, and ratings from different countries use different test conditions. Some Bangladesh listings carry BSTI star ratings. Read the label on the specific model, photograph it in the shop, and give efficiency real weight only if the AC will run many hours daily.
Current splits in Bangladesh commonly use R32 or R410A; very old or used units may carry older gases. For a buyer, the practical checks are: the refrigerant printed on the model plate, whether local technicians routinely handle it, and that the installer vacuums and leak-tests the lines. R32 and R410A differ in handling and environmental profile, so neither is automatically "better" for every situation. Match the exact refrigerant on the warranty card and memo.
Most AC disappointment in Bangladesh is installation, not the brand. Confirm with the installer:
No DIY instructions here on purpose: refrigerant handling and high-wall mounting belong to qualified installers.
Look for free airflow on all sides, a shaded or at least not sun-trapped position where practical, firm mounting, easy service access, a drain path for condensate, safe electrical routing and a reasonably short pipe run to the indoor unit. Hot air recirculating straight back into the unit is the classic rooftop mistake. For unusual spots such as glass facades or narrow shafts, use an experienced installer rather than improvising.
The cheapest sticker price is rarely the cheapest AC to own. Add up the full picture before deciding:
Total ownership cost = purchase + installation + electricity + maintenance + repairs.
Electricity dominates for heavy users, which is why a pricier efficient model can win over years while losing on day one. For light users the maths flips. Compare any two models with your own hours and tariff instead of trusting a generic payback claim. Warranty length, parts availability and service quality decide the repair term.
Do not shop by ranking. Compare what actually differs: local availability, warranty terms, authorised service points near you, parts availability, model range at your capacity, inverter options, efficiency labels, price and installation support. Browse the brand hubs: Gree, Walton, Daikin, Samsung, LG, General, Singer, Haier, Midea, Hisense, or start from all brands and the main AC price list.
Check the model's voltage range and rated current, the circuit's capacity, a correctly rated breaker, wiring condition and earthing. Most installations want a dedicated circuit for the AC. Have a qualified electrician handle anything beyond confirming what is already there.
Clean indoor filters every few weeks in peak season. Get coils, drains and the outdoor unit checked professionally once or twice a year in dusty or heavy-use conditions; lighter use stretches the interval. Low cooling, ice on pipes, water dripping indoors or rising noise all mean book a visit rather than waiting for the next schedule. Refrigerant top-ups without a leak check just repeat the expense.
Possibly undersized: runs for long stretches, never quite reaches the set temperature, corners stay warm. Possibly oversized: short on-off cycling, room cools fast but feels humid, and you paid more than needed. Treat these as clues, not diagnoses: poor installation, low gas, blocked filters and bad thermostat placement produce similar symptoms.
Start from roughly 1 ton per 100–130 sq ft, 1.5 ton per 130–180 sq ft and 2 ton per 180–260 sq ft, then adjust up for sun, top floors, high ceilings and extra occupants.
For most medium bedrooms, yes. Small shaded bedrooms often manage with 1 ton; large or sun-facing ones may need 2 ton.
Usually, when the AC runs many hours daily through summer. For rarely used rooms, non-inverter can cost less overall.
Often around 10 feet, with extra charged per foot. Confirm both numbers on your quotation, since the free length varies by seller.
Compressor, parts and service years separately, what voids cover, who honours it in your district, and a stamped card before the installer leaves.
Every few weeks in peak season; less often with light use. Clogged filters force longer run times and higher bills.
Yes, R32 appears on many current splits alongside R410A. Check the model plate rather than assuming.
Many current inverter splits list wide operating voltage and need none. Check your model's rated range and ask an electrician about local fluctuation first.
Same capacity, same technology, then price, efficiency label, features, warranty and installation terms. Use the price list and brand pages to line them up.
Every listing on this site carries a check date. Start from the main price list, filter to your capacity, then open the brand page for full model details. Match the exact model number against the seller's quotation, note the check date (prices move with promos and stock), and confirm warranty terms on the card, not from memory. If a listing and a seller disagree, the written quotation wins.